apply stain when air and wood surface temperatures are between 50 - 90 f; avoid applying in direct sunlight; dont apply stain if rain is in the forecast for the next 24-48 hours. it is ideal to stain your deck in a season that experiences mild temperatures. extreme heat or sun can work against you when you are staining your deck.
by applying the paint, varnish or finish before making the wood deck railing, water can be prevented from touching the bare wood. this simple technique also prevents peeling or cracking of the final finish. it is important to ensure that the wood deck railing finish is applied during good weather conditions.
update 2019 on pre-staining new wood decks before install. deckstainhelp.com has become the internets go-to site for professional wood deck staining tips. as before, we recommend you do not stain new wood prior to installation. instead, wait 3 months after installation before staining new wood surfaces.
that means staining as soon as possible after your deck is complete to prevent dust and dirt from accumulating on the surface of your deck. apply stain when the temps are between 50 and 90 degrees, and avoid staining in direct sunlight if possible. sun dries out stain quickly and can create uneven color or brush marks.
applying wood sealer to deck floor boards using a staining-pad. while spraying is the fastest way to apply deck stain, for most homeowners, using a roller or lambswool pad is one of the most practical ways to apply deck stain.
don't apply deck product in direct sun. the finish will dry too quickly and won't absorb into the wood. the best temperatures to apply deck stain are between 50 - 90 .
get the highest quality results from your deck or porch staining project by following these guidelines: before applying stain, make sure your deck has been cleaned properly. working with the wood grain, apply an even coat of stain using a 4-inch brush. for best results, avoid staining at midday
after the water test shows the mill glaze is no longer present, you can treat the deck with either an oil or water based stain. unlike interior stains, which only provide color, exterior decking stains provide both color and sealing protection.
the kind of stain you put on your deck and when you apply it depend on the type and condition of your treated wood. there are three basic categories of green-treated, or wolmanized, lumber. there are three basic categories of green-treated, or wolmanized, lumber.
before applying the stain, use painters tape to protect areas like the house's siding if needed. sweep the deck one more time to remove any leaves, dust, etc. that settled when the cleaner was drying. stir stain thoroughly before application and pour into a paint tray.
apply a wood deck cleaner and thoroughly scrub and or pressure wash lightly. neutralize with a wood brightener. these two steps will remove the mill glaze and 'open' the wood pores. apply a deck stain that is 'thin' in viscosity. a heavily bodied wood stain will have a hard time penetrating into the new wood.
applying twp deck stain to a newer deck too soon can result in a failed deck coating. the stain will trap moisture in the wood, which can cause several problems. mold and mildew can spread quickly underneath the stain eventually leading to rot and decay.
for the best results, you should stain cedar, redwood, exotic hardwoods and clear pressure-treated decks as soon as the deck is built and every spring afterward. however, green-treated, pressure-treated wood should be allowed to dry out for 30-90 days before applying the first stain.
follow these easy steps to stain a deck and restore its natural beauty. step 2 using a bristle brush to apply the stain, start by heavily coating the open-end grain of the boards. then brush two to three boards from one end to the other in long, smooth strokes. to avoid lap marks, make sure that the leading edge remains wet and that wet stain is brushed into wet stain.
a garden pump sprayer or a deck stain pump sprayer is the perfect tool to use to apply deck stain. you can finish a deck that would take days to stain by hand in a matter of a few hours with a pump sprayer.
step 2: preparation, preparation, preparation. if there is a build up of old stains on the deck, then the job gets a little tougher, but not impossible. instead of a sodium percarbonate cleaner you'll need to use a stain stripper. strippers are more caustic so follow the directions carefully.
how to: stain a wood deck if possible, avoid applying the stain in direct sunlight. always test the stain on a small area and let it dry to make certain the color is the one you want.
high temperatures are a big concern while applying the stain. if its too hot, the stain may dry too quickly, potentially causing lap marks and uneven penetration. avoid staining your deck if its above 90 degrees fahrenheit. to ensure this, either choose a cooler day or stain your deck in the morning before it gets too hot.
clean your wooden deck on a regular basis to remove all dirt, pollen, soot. use a deck brightener/deck wash to wash the surface without damaging the stain. keep your deck swept free of debris like leaves and other debris, including between boards. check for mold and mildew every few months.
use either an oil-based stain or a water-based stain. oil-based stains offer a deep, shiny finish while water-based stains provide a flat finish. follow the safety and application instructions on the label. apply stains at least 24 hours after wetting the deck.
prep the surface. the wood needs to be free of dirt and stains for the stain to adhere properly. start by sanding splintered spots, wearing a safety mask to avoid inhaling the dust. sweep the deck and use a putty knife to clean between the boards. clean the wood by applying a deck cleaner. or use a pressure washer , but if you do,