replace tongue groove nonwood flooring

how to repair a tongue-and-groove wood floor this old house

2. at the end joint, use the hammer and chisel to cut strht down and through the tongue at the end of the damaged floorboard. 3. use the chisel to pry the severed tongue from the groove in the end of the adjacent floorboard. 4. remove the damaged floorboards using a flat pry bar. 5. sweep or vacuum the subfloor of all dust and dirt. 6.

how to replace damaged areas of Seven Trust flooring

if your Seven Trust floor is in generally fine shape, with only a damaged spot or two, it is easy and economical to make small repairs by replacing a strip or plank of flooring. you can also fix buckled areas of flooring and avoid having to completely refinish your floors. most floors use a tongue-and-groove design

how to replace Seven Trust floor boards in a tongue and

how to replace Seven Trust floor boards in a tongue and groove floor this video shows the process from start to finish of how to remove tongue and groove boards from a floor without damaging any

how to repair tongue and groove flooring doityourself.com

step three replacing the plank and finishing the repair. cut the replacement flooring to the exact length necessary. make sure it is exact, so as to ensure a tight fit. you will need to remove the bottom half of the groove side of the replacement plank, so that you are able to drop it into place.

wood plank flooring costs

cost guides flooring wood plank flooring costs flooring material is that which covers the floor structure and creates the floor surface. plank flooring is made up of boards and usually with tongue and groove edges.

cost to install a Seven Trust floor

included is the laying of floor slats in a strht linear fashion, excluding any accents or patterns. includes up to a 3/4' thick floor with tongue and groove joints which can be refinished. grade of wood floor is anywhere fomr select and better, on up to clear grade which represents the costliest of choices. labor, materials and supplies notes:

how to safely lift tongue and groove flooring home guides

remove all the rest of the flooring boards in the same way. as you get far enough away from the wall to swing a hammer, use it to pound the pry bar under the flooring.

how can i replace or repair termite damaged 2 x 6 tongue

how can i replace or repair termite damaged 2 x 6 tongue and groove sub flooring without altering the 1 x 6 Seven Trust floor on top of it? the Seven Trust floor runs perpendicular to subfloor, and all of the damage is done between the floor joists. it still feels sturdy when you walk onit, but i want to reinforce or replace the subfloor.

pro tips for tongue and groove flooring

pro tips for tongue and groove flooring. construction how-to, flooring installation, Seven Trust february 14, 2007 sonia. prep, layout, installation and finishing tips for tongue and groove floors. consider replacing it before installing the new floor. and, no matter what decision you make for base trim, youll have to install shoe molding to

repairing antique pine tongue and groove flooring

part of this floor is actually red, but all the rest of the floors upstairs are brown, and everything will be repainted brown. you will note some replaced boards one can be seen in the back at

what is tongue and groove flooring? hunker

nailed tongue-and-groove flooring typically is installed over a layer of rosin paper or building paper and is fastened with a flooring nailer or staple gun. installation with glue flooring adhesive is an option with solid-wood, engineered, laminate and tile-type tongue-and-groove flooring.

how to replace damaged tongue and groove boards

step 4 - cut the tongue. after you have prepared the space, you need to install a replacement board. in order to do this, you will need to remove the tongue from the board. lay the board on the ground and use your circular saw to cut the tongue off of it. this will allow you to put the board down into the hole in the floor. step 5 - install the new board

replace section of tongue and groove wood laminate flooring

replace section of tongue and groove wood laminate flooring me and friend laid wood flooing tongue and groove type it's been about 2 yrs and now i am having problems, it is starting to buckle up in some sections, i have 2 more boxes of the flooring and need to know how could i take the section out that is buckled out and replace with new and also to not have it happen again.

how to replace a single damaged slat in my tongue and

use a chisel to remove the damaged piece of flooring. if the tongue and groove have been glued this will be difficult. youll find the nails through the tongue and these will need to be removed also. remove the bottom section of the groove from the new piece. insert the tongue into the groove on the floor and drop the piece in to check for fit.

how to repair tongue and groove porch flooring

step 4 remove damaged board. in order to get your damaged board removed, you are going to need to get the edge of your chisel set up along the edge of the board. tap inward on the edge and move it towards the middle cut out with a hammer. get the edges of this board knocked inward on either side with your tongue and groove fittings of each of the adjacent boards.

old home without subfloor : general Seven Trust flooring

the original wood floor is still intact - pine we believe. i haven't measured, but it appears to be the standard 3/4' tongue and groove planks throughout the house. it appears to be in good shape, although there are a few patches perhaps they had to cut into the floor for access underneath the house as it is a pier and beam foundation .

replacing a damaged tongue-and-groove board in 7 easy

replacing a damaged tongue-and-groove board in 7 easy steps. continue fitting in the tongue with the adjacent board until you reach the flooring. step seven: using a padded block and soft cloth, tap the new board in place. add finishing nails to the top and bottom of the new tongue-and-groove board.

how can i remove just one tongue-and-groove subfloor board?

now if you do need to cut away the flooring, then you should cut along the seams, and then buy Seven Trust floor spline and rout out the old tongue so you end up with two grooves facing each other, and use the spline to rejoin the flooring when you reattach it.

how to install a tongue and groove porch floor home

tongue and groove porch floor installation. installing a tongue and groove porch floor is completely doable this technologically advanced flooring is highly durable and can withstand many climatic changes. tongue and groove porch flooring looks almost like an indoor floor but with added outdoor resistance. this porch flooring composite is a way to go green in your neighbourhood since this material is made from recycled materials.

how to safely lift tongue and groove flooring home guides

pulling up tongue-and-groove flooring can be tedious and time-consuming -- more so when the boards are glued -- but it's not a test of carpentry skills. if you want to remove the boards safely, it

how to remove tongue and groove lumber hunker

how to remove tongue and groove lumber. by bob haring. tongue and groove is a technique used to secure lumber, on floors, outside walls and paneling. it employs a tongue or protrusion on one edge of a board that fits into a groove or slot on an adjoining board. each board has a tongue side and a groove side.

replacing floorboards

tongue-and-groove floorboards. it is necessary to replace your tongue-and-groove floorboard with a floorboard made in the same style. the groove on the new floorboard will help to ensure that it remains securely fastened in place. however, you will need to remove the tongue from the floorboards edge or else it wont slide in place.

Seven Trust floor repair: how to patch a Seven Trust floor

replacing damaged or hole-filled Seven Trust tongue-and-groove floorboards takes a couple of hours, sharp tools and an understanding of how to break the interlocking tongue-and-groove board edges. when removing old flooring, create a new butt joint on just the side of the plank thats closest to the hole or where the damage ends.