how to replace a rotted boat floor

replacing wood floor in lund aluminum fishing boat boat

replacing wood floor in alum. lund fishing boat hey, man, i like what you are saying. i have done lots of carpenter work, so it all sounds logical to me. would you go with 3/4 inch plywood for a nice steady ride, since the boat is light. my main question: will the epoxy and glass help protect that deck from water and thus rot ?

how to replace a floor in a boat gone outdoors your

how to replace a floor in a boat. however, the need for replacing a boat floor does not mean the end of your boating days. you can replace your floor in a short amount of time and with minimal labor. your boat will have a sturdier feel to it, and you'll be back out on the water in no time.

stringer repairs in fiberglass boats

you may be able to replace only the damaged portion, restoring the strength of the stringer while leaving it in position in the boat. because the wood in wood cored stringers is structural, any repairs you make to it have to be joined with a proper scarf.

4 mistakes to avoid when repairing a rotting boat floor

2. leaving rot behind. after you have cleaned the area, you will want to remove all of the damaged wood. this will be very easy to do because it will literally be crumbling. you cannot repair the boat floor while rotten wood remains as it will only continue to rot.

replacing the wood in the floors of my boat

way2slow. when you install the new floor and go to put the top back on, it won't fit. also, a very common thing to find with rotten a rotten floor is rotten stingers and wet floation foam the older boats used open cell foam that holds water better than a sponge , and they are totally no fun to replace.

boat floor dry rot doityourself.com

boat floor dry rot. there may be more than one sheet probably plywood . inspect them all, and replace the ones that are bad or questionable you don't want to do it all over again in a year or 2 replace flooring supports by fiberglassing in the appropriate pt lumber. the floorboards are usually just screwed into the stringers,

how to: remove a boat floor

how to build a boat floor that won't get hot - duration: 18:31. ryan moody fishing 111,183 views. replacing a rotted transom with coosa board - boat restoration - duration: 11:02.

how do you fix a spongy floor on a boat

if the floor is part of the boats hull, then take the boat out of the water allow it to dry completely. check the wood with a knife/screwdriver etc.. to see if it is rotted/flaky. if so

weekend warrior project

the biggest part of the job was removing the rotten wood and debris over two weekends. the total time spent on removal was about 15 hours. make sure that you're patient and take the time to let

signs it's time to fix your boat stringers doityourself.com

boat stringers are the lengths of wood under the boat deck that support it, much as joists would support the floor in your home. they receive much harsher treatment than joists, however, and that means theyll periodically need to be repaired or replaced.

question of cost for stringer, floor and transom replacement

re: question of cost for stringer, floor and transom replacement funny thing about spending time working on this project vs fishing is, the best time to fish for catfish is the winter months, which is probably not the best time to be working on a boat project with no garage.

newby replacing aluminum boat's floor boat design net

now, they're all rotted out. point of terminology- the flat part of the boat on which you walk is the 'sole', a 'floor' is one of the structural members underneath it which transfers load from the sole to the hull. some of the more puritanical boat restorers on here will no doubt bash me for what i'm about to suggest. but given your constraints:

replacing boat floor page: 1

don s. re: replacing boat floor depends on how your floor got soft or rotten to begin with, usually when the floor is bad it has leaked into the hull of the boat, causing the stringers, support beams, to rot. most of the time this is all caused by leaving the boat in the weather.

removing rotted plywood from under fiberglass floor?? page

take out enough of the old, rotted deck to inspect the hull underneath from bow to stern. at the very least, you'll probaby want to rip out and replace the entire deck not a hard job, lots of posts on this forum to guide you, just do a search and spend some time reading.

boat repair: alternative transom, deck and stringer boat

the repair can be easy or difficult depending on the extent to the rot and the construction of the boat. there are three basic techniques: top, outside and inside. the top method is easiest if

replacing rotten floor on aluminum boat page: 1

replacing rotten floor on aluminum boat. it is always a good idea to have access to the hull of the boat just in case water gets between the deck and the hull. you will need to have a way to get the water out. a bilge allows water to drain from under the deck to the bilge and out a drain hole in the transom.

replace deck joists in 6 steps doityourself.com

the joists are a major component of the framework and rotting joists can affect the structural integrity of the deck. if replacing one or more joists, you will want to do so without rebuilding the entire deck. this article will explain how to go about replacing deck joists in 6 easy steps. step 1 - obtain the replacement joists

bass boat floor repair page: 1

bass boat floor repair. underneath was all the nasty water-logged foam, partially rotted stringers, etc. woohoo. the hull has 6 stringers - the main box, and two to each side. the main box stringers and the two to the outside of the hull are strong, so i'm going to mount 2x4s on the sides of the rotted ones in the middle for strength.

easiest way to replace a rotted floor in a 14 ft

best answer: if the floor is rotten then you may find that the stringers are rotten also. remove the old floor and check the stringers. replacement is done by rebuilding the stringers if necessary adding new floatation and replacing the floor with marine plywood sealed . here is a great site with full instructions.